AIROX GRC-1000 NEBULIZER It was created for high flow rates and for dedusting large areas. Combined with the DANCERFOG mobile system for wide range coverage of park areas. Available in Aluminum and/or Stainless Steel according to application requirements.

AIROX IMPACT - NEBULIZER The most loved and widespread AIROX series The strength of IMPACT technology is in the micronization of water at low pressures. Thanks to the external micronization of the nozzle, the risk of clogging of the pipes is considerably reduced and dripping phenomena are avoided. Interchangeable heads, components in STAINLESS STEEL and/or BRASS according to the application needs.

With a single nebulizer, wide diffusion of artificial fog obtained by micronizing water at low pressures thanks to our IMPACT technology. Easy to install and calibrate.

Aluminum joints suitable for textile belts of bucket elevators with load up to 1250 N/mm

This large-volume mixer is a new development. It requires only low electrical connected loads. It mixes accurately, effectively and very gently. Gyraton® mixers are also particularly cost-effective because they require very little installation space. The properties of the mixing goods are irrelevant. Even moist or poorly flowing materials (time-solidifying materials) are homogenized. The function is similar to all other amixon® mixers. But the specific energy input is lower with the Gyraton® mixer. The mixer spiral rotates slowly and conveys the mixed materials upwards. It always touches only a part of the mixing chamber wall. In addition to rotation, the mixer shaft performs a circular path above the mixing chamber floor. The pivot point of the shaft lies in the plane of the gas-tight shaft seal. The entire cylinder surface is tangent to the mixing element spiral. This also applies to the bottom. Mixing takes place without dead space because the base is designed as a calotte. The lower mixing unit arm has the same curvature as the calotte shell. The mixer shaft is only supported and driven at the top. The shaft sealing is permanently hygienic and gas-tight. The unit shown here can homogenize 70 m³ of mix. This is the content of a 40-foot deep-sea container. This mixer design requires very little installation space. The mixer can optionally have one or more discharge nozzles. In the amixon® pilot plant, such a Gyraton® mixer is available for tests. The usable volume is 3 m³. From the measurement data that amixon® obtains during the mixing test, we can calculate very accurate design data for larger Gyraton® mixers.

Excessive vibration can disperse energy and create unwanted sounds and noise. The vibration and noise produced by some machinery can permeate through the air and the structures thereby, negatively influencing the functionality of other machines and/or sensitive equipment. The conscious use of certain products can significantly reduce the effects of these harmful vibrations. This can greatly increase the efficiency of both machinery and operations as well as creating a better working environment by attenuating the noises and stresses that the vibrations can generate.

Material Load: - impact rails: absorb the force of material loading and protect the roller bearings - the plates flex under the loading shock, discharging the force on the frame through the impact rails, thus protecting the roller bearing - once the material is loaded, the plates are stiff enough to flex back and proceed supported by the rollers without contact with the impact rails Plates: - thick steel sections forces the material to follow the plates even during the hardest extractions under a full hopper - the anti-spillage lip is in special armoured steel and ensures continuous contact between two adjacent plates, minimisibg material spillage Wheels and chains: - drive wheels are made in high alloy steels with replaceable toothed segments - the parts in contact with the chain are induction-hardened to extend their operating file - the chains with pins and fixed bushes are in high alloy steel, induction-hardened on the wear surfaces Pins and bushes are tempered to ensure a very long wear life A complete range of strong apron feeders is available for the heavy duty extraction of material from hoppers under waggon tipper or truck unloader. The Apron Feeders are designed for robustness and effectiveness of processes: they can reach over 3600 millimeters ub width; the pans ae built in tick steel profiles, reinforced with beams, with a shock absorbing systems that protects the bearing of the rollers from the impact shocks They can extract hoghly abrasive materials with grain size up to 1500 millimeters. They can be fully dismountable to be retrofitted into your existing bunkers

It's all about combining things. Gas and dust approvals in one device. Our ATEX All-in-One sensors are approved for reliable and safe level control in all hazardous areas, thanks to our certifications for zones 0, 1 and 2 (gas) and 20, 21 and 22 (dust). The sensors do not require an Ex barrier. The All-in-Ones are available from size M8 up to M32. They can be supplied with the EasyTeach by Wire function and with food certification.

T400 ELITE: monitor for PTC type temperature probes; Temperature probes available with different types of thermistors; TOUCHSWICH: anti-skidding with non-inductive contact; rotation indicators with relative support

Muller Beltex specialises in delivering high quality (ATEX) process monitoring systems for the agricultural and industrial bulk and processing industries. With our extensive product range and comprehensive know-how, we always find the right solution in any industry for the clear and efficient monitoring of your installation. This not only enhances safety of your environment, it also means fewer component replacements and lower maintenance cost. Belt misalignment, bearing temperature, slip detection and much more to prevent heat sources create a combustible dust explosion.

Atexon® spark detection and extinguishing systems by IEP Technologies are designed to protect industrial processes by helping reduce the risk of ignition sources such as burning embers from reaching protected equipment. The system detects sparks and extinguishes them automatically without interrupting process operations. The small amount of water extinguishant used, approximately five liters, will greatly limit any interruption to filters or other production machines. Once the ignition source has been mitigated, the system automatically resets to normal operations and is ready to extinguish new ignition sources.

The automatic big bag cutting device designed and created by Stawimpianti match the manufacturing companies needs, which increasingly require safety and speed in emptying big bags and avoiding the contribution of human operators for the activities of hooking, emptying and removing the big bags. The possibility of preloading the necessary quantity of big bags to be cut and the simple, linear and continuous operation of the machine allow cutting up to 25 big bags per hour. The compactor and the integrated dedusting system guarantee powder total confinement and the reduction of the volume of the whole amount of bags cutted.